Programming remains the biggest & most critical component of test case automation. Hence designing & coding of test cases is extremely important, for their execution and maintenance to be effective.

Some fundamental attributes of good automated test cases which can be followed,

• Simple
• Modular
• Robust
• Reusability
• Maintainable
• Documented
• Independant

1) Simplicity: The test case should have a single objective. Multi-objective test cases are difficult to understand and design. There should not be more than 10-15 test steps per test case, May be depending on the process steps may increase. However 10 to 15 steps note a good clarity test case. Multipurpose test cases are likely to break or give misleading results. If the execution of a complex test leads to a system failure, it is difficult to isolate the cause of the failure.

2) Modularity: Each test case should have a setup and cleanup phase before and after the execution test steps, respectively. The setup phase ensures that the initial conditions are met before the start of the test steps. Similarly, the cleanup phase puts the system back in the initial state, that is, the state prior to setup. Each test step should be small and precise. However we can’t expect all test cases to have set up and cleanup process, it may vary accordingly.. The test steps are building blocks from reusable libraries that are put together to form multi-step test cases.

3) Robustness and Reliability: A test case verdict (pass or fail) should be assigned in such a way that it should be unambiguous and understandable. Robust test cases can ignore trivial failures such as one pixel mismatch in a graphical display. Care should be taken so that false test results are minimized. The test cases must have built-in mechanisms to detect and recover from errors. For example, a test case need not wait indefinitely if the software under test has crashed. Rather, it can wait for a while and terminate an indefinite wait by using a timer mechanism.

4) Reusability: The test steps are built to be configurable, that is, variables should not be hard coded. They can take values from a single configurable file(Data Tables). Attention should be given while coding test steps to ensure that a single global variable is used, instead of multiple, decentralized, hard-coded variables. Test steps are made as independent of test environments as possible. The automated test cases are categorized into different groups so that subsets of test steps and test cases can be extracted to be reused for other platforms and/or configurations. Finally, in GUI automation hard-coded screen locations must be avoided.

5) Maintainability: Any changes to the software under test will have an impact on the automated test cases and may require necessary changes to be done to the affected test cases. Therefore, it is required to conduct an assessment of the test cases that need to be modified before an approval of the project to change the system. The test suite should be organized and categorized in such a way that the affected test cases are easily identified. If a particular test case is data driven, it is recommended that the input test data be stored separately from the test case and accessed by the test procedure as needed. The test cases must comply with coding standard formats. Finally, all the test cases should be controlled with a version control system.

6) Documented: The test cases and the test steps must be well documented. Each test case gets a unique identifier, and the test purpose is clear and understandable. Author name, date of creation, and the last time it was modified must be documented. There should be traceability matrix to the features and requirements being checked by the test case. The situation under which the test case cannot be used is clearly described. The environment requirements are clearly stated with the source of input test data (if applicable). Finally, the result, that is, pass or fail, evaluation criteria are clearly described.

7) Independent and Self-sufficient: Each test case is designed as a cohesive entity, and test cases should be largely independent of each other. Each test case consists of test steps, which are naturally linked together. The predecessor and successor of a test step within a test case should be clearly understood.

Tagged as: Automated Testing, Quality assurance and testing, Quality Assurance and Testing Services, software quality assurance

You might want to read these awesome related posts

• How to achieve full potential of Test Automation?
• Automation Feasibility Checklist
• SAP TAO and Panaya – Complementers and not competitors
• Pre-requisites for General Automation
• HexaFLOW GRABBER